View GP1A73A_523487.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

GP1A73A/GP1A73A1
GP1A73A/GP1A73A1
s Features
1. Compact type 2. TTL compatible owing to OPIC output 3. Snap-in mounting type 4. 3 kinds of mounting plate thickness (Applicable plate thickness : 1.0, 1.2 and 1.6 mm)
Compact OPIC Photointerrupter with Connector
s Outline Dimensions
GP1A73A
( 6.8)
SHARP JAPAN
(Unit : mm)
8.0
7.8
73
2.3 (Sensor center)
JAPAN AMP made connector 175487-3 4.7 2-0.5 0.1 (Slit) 3.2 1 : VCC 2 : Vout 3 : GND
(Case surface) 13.6 4.3 5.0 4.3 1.6 6.8 1
7.2
1.1
0.6 0.2 2.3
1.1
1. Copiers 2. Laser beam printers 3. Facsimiles
5.6
s Applications
5.8
2.4 5.4 6.9 9.9 11.4 2.3
2-0.9 2-0.5 4.0
* Unspecified tolerances shall be as follows. * ( ) : Connector dimensions for reference Dimension d < 5.0 5.0<= d < 15.0 15.0 <= d Tolerance
1.2 0.75
14.0 16.8 17.0
0.15 0.2 0.3
GP1A73A1
( 5)
SHARP JAPAN
8.0
8.0 HIROSE made connector DF3A-3P-2DSA 4.7 2-0.5 0.1 (Slit) 3.2 3 : VCC 2 : Vout 1 : GND 1.6 5.0 1 5
2.3 (Sensor center)
(Case surface) 13.6 4.3 5.0 4.3
* "OPIC" (Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and signal-processing circuit integrated onto a single chip.
7.2
s Absolute Maximum Ratings
Parameter Supply voltage Output voltage Low level output current Operating temperature Storage temperature Symbol VCC V out IOL T opr T stg
(Ta=25C) Rating - 0.5 to + 7 - 0.5 to + 7 8 - 20 to + 75 - 30 to + 85 Unit V V mA C C
5.6
73
1.1
0.6 0.2 2.3
1.1
2.4 5.4 6.9 9.9 11.4 2.3
2-0.9 2-0.5 4.0
*1 *2 *3 *3
1.2 0.75
14.0 16.8 17.0
* Unspecified tolerances shall be as follows. * ( ) : Connector dimensions for reference Dimension d < 5.0 5.0<= d < 15.0 15.0 <= d Tolerance
*1 Output transistor collector-emitter voltage *2 Output transistor collector current *3 The connector should be plugged in/out at normal temperature.
0.15 0.2 0.3
s Internal Connection Diagram (Both GP1A73A/GP1A73A1)
Constant voltage circuit
GND Vout
Connector terminal No. GP1A73A GP1A73A1 3 : GND 1 : GND 2 : Vout 2 : Vout 1 : Vcc 3 : Vcc
Amp. Vcc * GP1A73A and GP1A73A1 are different in the terminal marking number of connectors from each other due to use of connectors of different manufacturers.
" In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device."
GP1A73A/GP1A73A1
s Electro-optical Characteristics
Parameter Operating supply voltage Current consumption Low level output voltage Current consumption High level output voltage Response characteristics MIN. interruption time Symbol VCC ICCL VOL ICCH V OH tH RL = 4.7k MIN. sensing time tL 166 s (VCC =5v, Ta=25 C unless otherwise specified) Conditions MIN. 4.5 Light beam uninterrupted Light beam uninterrupted, I OL =4mA Light beam interrupted Light beam interrupted, RL =47k VCC x 0.9 166 TYP. MAX. 5.5 16.5 0.35 16.5 Unit V mA V mA V s
Fig. 1 Output Current vs. Ambient Temperature
10
Fig. 2 Low Level Output Voltage vs. Low Level Output Current
1.0 0.5 V CC = 5V T a = 25C
8
Low level output voltage V OL ( V)
(mA)
OL
0.2 0.1 0.05
6
Output current I
4
2
0.02 0.01
0 - 20
0
25
50
75
1
2
5
10
20
50
100
Ambient temperature Ta (C)
Low level output current I OL ( mA)
Fig. 3 Low Level Output Voltage vs. Ambient Temperature
0.2 V CC = 5V
Fig. 4 Supply Current vs. Supply Voltage
20
Low level output voltage V OL ( V)
I OL = 6mA 4mA
CC ( mA)
- 20CI CCL - 20CI CCH
Supply current I
0.1
10
+25CI CCL +25CI CCH +75CI CCL +75CI CCH
2mA
0 - 25
0
25
50
75
100
0
4.5
5.0
5.5
- 20 Ambient temperature Ta (C)
Supply voltage V CC ( V)
GP1A73A/GP1A73A1
Fig. 5 Detecting Position Characteristics (1) Fig. 6 Detecting Position Characteristics (2)
Output "High" VCC= 5V, Ta= 25C RL= 47k Detecting position characteristics ( d= 2.35 0.3mm )
d0 Shield plate
Output "High" VCC= 5V Ta= 25C RL= 47k Detecting position characteristics ( h= 3.0 + 0.3 ) - 1.8
Shield plate 0 h
Output "Low"
Output "Low"
0
1
2
3
4
5
0
1
2
3
4
5
Distance d (mm)
Distance h (mm)
s Recommended Mounting Hole Shape
8 - R0.1 0.1 8 - R0.1 0.1
(Unit : mm)
8 - R0.1 0.1 3.5
General mounting type
7.5
17
6 17
7.5
6
7.7
7.5
7.5
Plate thickness : 1.6 mm
12 - R0.1 0.1
Plate thickness : 1.2 mm
12 - R0.1 0.1
Plate thickness : 1.0 mm
12 - R0.1 0.1 3.5
Reverse insertion preventive type
7.5
17
6
17
3.5 2.4 7.5 2.4
7.5
6
2.4 7.7
2.4
2.4 7.5
2.4
Plate thickness : 1.6 mm
Plate thickness : 1.2 mm
Plate thickness : 1.0 mm
1. It is recommended to mark the shear droop surface (punch side) of the mounting plate (metal plate) with "GP1A73A" or "GP1A73A1". 2. Mounting workability, shaking after mounting and mounting strength depend on the corner radius of the mounting plate and state of punching. Determine the mounting dimensions after check on an actual machine. 3. General dimensional tolerances shall be 0.1 mm.
3.5
17
17
GP1A73A/GP1A73A1
(Precautions for Operation)
1) In this product, the PWB is fixed with a hook, and cleaning solvent may remain inside the case; therefore, dip cleaning or ultrasonic cleaning are prohibited. 2) Remove dust or stains, using an air blower or a soft cloth moistened in cleaning solvent. However, do not perform the above cleaning using a soft cloth with solvent in the marking portion. In this case, use only the following type of cleaning solvent for wiping off; Ethyl alcohol, Methyl alcohol, Isopropyl alcohol, When the cleaning solvents except for specified materials are used, please contact us. 3) In order to stabilize power supply line, connect a by-pass capacitor of more than 0.01 F between VCC and GND near the device. q As for other general precautions, please refer to the chapter "Precautions for Use".

▲Up To Search▲

Price & Availability of GP1A73A

	To Download GP1A73A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .